Special Paint

Special Paint

-For use at all kinds of high temperature equipment -For use petroleum pipeline or oven.

Product details

725-W61-22 Organo silicone high-temperature resistant paint-Silver

 

Product Description

-One pack, dry at room or higher temperature

-On surface likely to reach up to 300600℃

-VOC less than 535g/L

Intended Use

-For use at all kinds of high temperature equipment

-For use petroleum pipeline or oven.

 

 

 

 

 

 

 

 

 

 

 

 

 

Product Information

Volume Solids

40%±2%

Finish/Sheen

 

Gloss

 

Typical Film Thickness

 

30microns dry (75microns wet)

 

Theoretical Coverage

 

13.3m2/L at typical film thickness

 

Mix Ratio

 

One pack

 

Method of Application

 

 

Airless Spray

 

Recommended

 

 

Tip size range

0.38-0.53mm

 

 

 

Output pressure

≥17MPa

 

Air Spray

 

Tip size range

2.0-3.0mm

 

 

Output pressure

≥0.4MPa

 

Brush/Roller

 

For small area only

 

 

Thinner

 

Not recommended. Use only in exceptional circumstances (volume 5%)

 

Cleaner

JX-601

Induction Period

 

Not applicable

Drying Information

 

10℃

25℃

35℃

Touch Dry

1h

30min

20min

Hard Dry

8h

6h

3h

Pot Life

Not applicable

Overcoating Data       Substrate Temperature

Overcoated by

10℃

25℃

35℃

Min Max

Min Max

Min Max

725-W61-22

8h

6h

3h

 

Storage

Store in cool and dry conditions. Well ventilate. Keep away from hot and fire. Shelf Life: 12 months minimum at 25℃. Subject to re-inspection thereafter.

Pack Size

21.6kg/18L in 20L container

Flash Point

Greater than 28℃

 

 

 

 

 

 

 

 

urface Preparation

All surfaces to be coated should be clean, dry and free from contamination.

 

 

Abrasive Blast Cleaning

 

Abrasive blast clean to Sa2½GB/T8923.1-2011. If oxidation has occurred between blasting and application of 725-W61-22, the surface should be reblasted to the specified visual standard.

 

Surface defects revealed by the blast cleaning process should be ground. Filled, ortreated in the appropriate manner.

 

Repair

 

The areas to be repaired should be cleaned to St3GB/T 8923.1-2011by  mechanical method or higher level of surface prepared to Sa2.5GB/T 8923.1-2011by abrasive blasting. Abrade the area immediately surrounding the repair to provide a key for subsequent coating application. Overlap areas should be kept to a minimum.

 

 

 

 

Limitations

Apply in good weather. Temperature of the surface to be coated must be least 3℃ above the dew point when the humidity is lower than 85%.

 

The dry time and overcoating interval may change according to the environment factors.

 

Avoiding absorb the solvent steam and paint steam for long time. Skin and eyes must avoid contacting the paint. Pay attention to ventilate and fireproof when applying.

 

 

Duty statement

The data in the sheet base on the information from the laboratory and practice. The application may exceed the control, so we only ensure our product quality. We own the right of the data sheet modification without informing.

 

Hot Tags: special paint, China, suppliers, manufacturers, factory, Asia, Africa, made in China
Feedback

Our Service

The company has been developed a series of ship coating products have been passed approval by CCS, LR, and DNV. The coatings systems hold independent intellectual property rights meet the requirements of corrosion on steel and concrete structures in harbors, wharfs, bridges, power stations, petrol-chemicals and civil engineering.

Feedback

Contact Us

Address:Room 214 2F No.149-2 Huangpu AVE Middle, TianHe District, Guangzhou City, China

Tel: +86-20-38993165

Fax: 86-20-38993165

E-mail: sales@huisinschem.com

CopyRight© Huisins New Material Technology Co.,Limited

Huisins New Material Technology Co.,Limited