Multicolor Tin Free Self Polishing Marine Antifouling Paint Corrosion Resistant Boat Spray Coating 450g/L

Detailed Product Description Tin-Free Self Polishing Antifouling Paint Marine Spray Paint Product Description • A high performance tin-free self polishing antifouling paint • Tributyl Tin(TBT) free • VOC less than 450g/L Intended Uses • For use at Newbuilding-or Maintenance and Reair. Product...

Product details

Detailed Product Description

Main Raw Material:EpoxyStandard Film Thickness:90 Microns Dry ( 180 Microns Wet)
Application Method:SprayColor:Multicolor
Type:TopcoatLuster:Half Glazed
Theoretical Spreading Rate:200Solids (vol %):≤450g/L


Tin-Free Self Polishing Antifouling Paint Marine Spray Paint
Product Description

• A high performance tin-free self polishing antifouling paint
• Tributyl Tin(TBT) free
• VOC less than 450g/L

Intended Uses
• For use at Newbuilding-or Maintenance and Reair.

Product Information
• Volume Solids 50%±2%
• Finish/Sheen Matt
• Typical Film Thickness 90 microns dry (180 microns wet)
• Theoretical Coverage: 5.5㎡/lat typical film thickness
• Mix Ratio: one pack
• Method of Application
   Airless Spray Tip size range 0.48-0.63mm
   Output pressure ≥17mpa
   Air Spray Tip size range 2.0-3.0mm
   Output pressure ≥0.4mpa
   Brush/Roller For small area only
• Thinner: Not recommended. Use water only in exceptional circumstances(Max5% by volume)
• Drying Information 
   -5°C 5°C 25°C 35°C
   Touch Dry 2H 1H 30min 15min
   Hard Dry 24H 20H 12H 8H
   Pot Life Not applicable
   Overcoatings Data: Substrate Temperature
   Overcoated By 
   5°C 15°C 25°C 35°C
   Min Max Min Max Min Max Min Max
   24H no 20H no 12H no 8H no
• Storage: Store in cool and dry conditions, Well ventilate. Keep away from hot and fire.Store temperature should be higher than 0°C.
   Shelf Life: 12Months minimum at 25°C.Subject to re-inspection thereafter.
• Pack Size: 24.7KG/18L in 20L container
• Flash Point: Greater than 31°C

Limitations
• Coating lifetime is directly proportional to thickness applied. Performance of the product is dependant upon the specified film thickness being achieved.
• After the last coating dried,it should be flood into water in 15days. If these periods are exceeded the antifouling performance may be impaired.
• The color of coating may be changed into gray or celadon after flooded into water.
• Apply in good weather. Temperature of the surface to be coated must be least 3°C above the dew point when the is lower than 85%
• In common with all epoxy base coatings, this product will exhibit chalking of the film on UV exposure.
• The dry time and over coating interval may change according to the environment factors.
• Avoiding absorb the solvent steam and paint steam for long time. Skin and eyes must avoid contacting the paint. Pay attention to ventilate and fireproof when applying.

Anticorrosion & antifouling protective for ship supporting system

15-1.jpg

Anti-corrosion anti-fouling system of shipping form a complete set for 2000 cubic dredger in India

15-2.jpg

15-3.jpg


Related Products
Feedback

Our Service

The company has been developed a series of ship coating products have been passed approval by CCS, LR, and DNV. The coatings systems hold independent intellectual property rights meet the requirements of corrosion on steel and concrete structures in harbors, wharfs, bridges, power stations, petrol-chemicals and civil engineering.

Feedback

Contact Us

Address:Room 214 2F No.149-2 Huangpu AVE Middle, TianHe District, Guangzhou City, China

Tel: 86-20-38993165

Fax: 86-20-38993165

E-mail: sales@huisinschem.com

CopyRight© Huisins New Material Technology Co.,Limited

Huisins New Material Technology Co.,Limited