Multipurpose Epoxy Anti-corrosive Paint Topside and Superstructure Coating Quick Drying Universal Primers Colors

Detailed Product Description Product Description • A epoxy universal primer with good corrosion and abrasion resistance • Suitable for application at low temperature • VOC is 280 g/L Intended Uses • Use in all parts from keel to handrail • Suitable for use with controlled cathodic protection •...

Product details

Detailed Product Description

Main Raw Material:EpoxyStandard Film Thickness:125microns Dry ( 186 Microns Wet)
Application Method:SprayColor:Red/Grey
Type:PrimerLuster:Half Glazed
Theoretical Spreading Rate:150Solids (vol %):280 G/L


Product Description
• A epoxy universal primer with good corrosion and abrasion resistance
• Suitable for application at low temperature
• VOC is 280 g/L

Intended Uses
• Use in all parts from keel to handrail
• Suitable for use with controlled cathodic protection
• For use at Newbuilding,Maintenance and Repair or On Board Maintenance

Product Information
• Volume Solids 67%±3%
• Finish/Sheen Seim-Gloss
• Typical Film Thickness 125microns dry ( 186 microns wet)
• Theoretical Coverage: 5.4㎡/L at typical film thickness
• Mix Ratio: 3.2:1 6.5:1
• Method of Application
   Airless Spray Tip size range 0.38-0.53mm
   Output Pressure ≥17MPa
   Air Spray Tip size range 2-3mm
   Output Pressure ≥0.4MPa
   Brush/Roller Need to coat several times to get film thickness
• Thinner: Not recommended. Use water only in exceptional circumstances(max 5% by volume)
• Drying Information 
   -5°C 5°C 25°C 35°C
   Touch Dry 6H 4H 2H 1H
   Hard Dry 36H 24H 18H 12H
   Pot Life 6H 4H 2.5H 1.5H
   Overcoatings Data: Substrate Temperature
   Overcoated By 
   -5°C 5°C 25°C 35°C
   Min Max Min Max Min Max Min Max
   725-h06-51 48H no 36H no 24H no 12 H no
   725-J43-5 48H no 36H no 24H no 12 H no
   725-BS43-91 72H no 36H no 24H no 12 H no
   725-H42-30 36H no 24H no 18H no 12 H no

• Storage: Store in cool and dry conditions, Well ventilate. Keep away from hot and fire.Store temperature should be higher than 0°C.
   Shelf Life: 12Months minimum at 25°C.Subject to re-inspection thereafter.
• Pack Size:
   Part A 29.2kg/15.5L in 20L container
   Part B 4.5KG/4.5L in 6L container
   Surface Preparation: The surface should be cleaned oil or grease, dust, and other foreign matter to keep clean and dry.

Surface Preparation:
1. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. All surfaces to be coated should be clean, dry and free from contamination.
2. Newbuilding
Remove weld spatter and smooth weld seams and sharp edges. The surfaces should be blast cleaned to Sa2.5(GB/T8923-1988). The weld seams areas could be to St3(GB/T8923-1988)
Apply 725-H06-51 before oxidation occurs. If oxidation has occurred, The entire oxidized area should be reblasted to the standard specified above.
3. Repair/On Board Maintenance
The areas to be required should be cleaned to St3(GB/T 8923-1988) by mechanical method or higher level of surface prepared to Sa2.5 by abrasive blasting. Abrade the area immediately surrounding the repair to provide a key for subsequent coating application. Overlap areas should be kept to minimum.

Limitations
• This product will not cure adequately below 5°C.For maximum performance ambient curing temperature should be above 10°C
• Apply in good weather, Temperature of the surface to be coated must be least 3°C above the dew point when the humidity is lower than 85%
• In common with all epoxy base coatings. 725-H06-19 will exhibit chalking of the film on UV exposure.
• The dry time and over coating interval may change according to the environment factors.
• Forbid to trample or pullute the surface of AF3-1 and coat the next paint before the film is hard dry.

9-1.jpg


Related Products
Feedback

Our Service

The company has been developed a series of ship coating products have been passed approval by CCS, LR, and DNV. The coatings systems hold independent intellectual property rights meet the requirements of corrosion on steel and concrete structures in harbors, wharfs, bridges, power stations, petrol-chemicals and civil engineering.

Feedback

Contact Us

Address:Room 214 2F No.149-2 Huangpu AVE Middle, TianHe District, Guangzhou City, China

Tel: 86-20-38993165

Fax: 86-20-38993165

E-mail: sales@huisinschem.com

CopyRight© Huisins New Material Technology Co.,Limited

Huisins New Material Technology Co.,Limited