Marine Spray Paint Cargo Hold Coaing Epoxy Ballast Tank Coating Red Grey

Detailed Product Description Product Description 1. A two pack epoxy heavy-duty anticorrosive coating 2. Suitable for application at low temperature 3, VOC less than 230g/L Intended Uses • Use in seawater ballast tanks in all types of ships. • For use in heavy-duty anticorrosive areas of steel...

Chat Now
Product details

Detailed Product Description

Main Raw Material:EpoxyStandard Film Thickness:160μm Dry ( 222μm Wet)
Application Method:SprayColor:Multicolor
Theoretical Spreading Rate:200Solids (vol %):230g/L

Product Description
1. A two pack epoxy heavy-duty anticorrosive coating
2. Suitable for application at low temperature
3, VOC less than 230g/L

Intended Uses
• Use in seawater ballast tanks in all types of ships.
• For use in heavy-duty anticorrosive areas of steel structure.
• For use at Newbuilding-or Maintenance and Repair and Repair or On Board Maintenance.

Product Information
• Volume Solids 72%±2%
• Finish/Sheen Matt
• Typical Film Thickness 160μm dry ( 222μm wet)
• Theoretical Coverage 4.5㎡/lat typical film thickness
• Mix Ratio: 3:1(Volume) 4.3:1(mass)
• Method of Application
   Airless Spray Tip size range 0.38-0.53mm
   Output pressure ≥17mpa
   Brush/Roller For small area only
• Thinner: Not recommended. Use water only in exceptional circumstances(Max5% by volume)
• Drying Information
   -5°C 5°C 25°C 35°C
   Touch Dry 6H 4H 2H 1H
   Hard Dry 36H 24H 18H 12H
   Pot Life 6H 3H 1.5H 1H
   Overcoatings Data: Substrate Temperature
   Overcoated By
   -5°C 5°C 25°C 35°C
   Min Max Min Max Min Max Min Max
   725-H53-201 24H No 20H No 8H No 6 H No
• Storage: Store in cool and dry conditions, Well ventilate. Keep away from hot and fire.
   Shelf Life: 12Months minimum at 25°C.Subject to re-inspection thereafter.
• Pack Size:
   Park A 24KG/13.5L in 20L container
   Park B 6KG/6.5L in 9.25L container.
• Flash Point:
   Park A greater than 31°C
   Park B greater than 29°C
   Mixed paint greater than 31°C

Surface Preparation:
1. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. All surfaces to be coated should be clean, dry and free from contamination.
2. Newbuilding
Remove weld spatter and smooth weld seams and sharp edges. The surfaces should be blast cleaned to Sa2.5(GB/T8923-1988). The weld seams areas could be to St3(GB/T8923-1988)
Apply 725-H53-201 before oxidation occurs. If oxidation has occurred, The entire oxidized area should be reblasted to the standard specified above.
3. Repair/On Board Maintenance
The areas to be required should be cleaned to St3(GB/T 8923-1988) by mechanical method or higher level of surface prepared to Sa2.5 by abrasive blasting. Abrade the area immediately surrounding the repair to provide a key for subsequent coating application.Overlap areas should be kept to minimum.

Apply in good weather. Temperature of the surface to be coated must be least 3°C above the dew point when the is lower than 85%
In common with all epoxy base coatings, this product will exhibit chalking of the film on UV exposure.
The dry time and over coating interval may change according to the environment factors.
Avoiding absorb the solvent steam and paint steam for long time. Skin and eyes must avoid contacting the paint. Pay attention to ventilate and fireproof when applying.


Related Products

Our Service

The company has been developed a series of ship coating products have been passed approval by CCS, LR, and DNV. The coatings systems hold independent intellectual property rights meet the requirements of corrosion on steel and concrete structures in harbors, wharfs, bridges, power stations, petrol-chemicals and civil engineering.


Contact Us

Address: Room 603 6F No 140 Huagang Business Building Zhongshan AVE West, TianHe District, Guangzhou City, China

Tel: +86-20-38993165

Fax: 86-20-38993165


CopyRight© Huisins New Material Technology Co.,Limited